• A. Easy put and handling as liquid water treatment product
• B. Usable up to boiler pressure 50 BAR
• C. By preventing scale and corrosion, increase system life/stability
• D. Contain activeamine neutralized acid, occurring in watering and condensate water system
• E. Remove sludge and solid easily by dispersion and Blow Down
• F. Keep boiler tube surface clean, improve heat transfer
• G. Simple test
• H. High concentration product

• A. Prevent scale and corrosion, remove sludge, improve pH in boiler

• A. Best method is continuous putting by using Chemical Dosing System(Metering equipment), it is possible put in cascade tank at a time
• B. Input spot
  • 1) Cascade Tank, Feed Pump entrance, Feed Pump exit
  • 2) During bolier operation, put in Feed Pump entrance/exit,Cascade Tank for 24 hours continuously through metering equipment
  • 3) As high alkalinity Chemical(1% solution pH13-14), if put a large amount at once, occur alkali corrosion on feed water system
  • 4) If boiler watering antiscales injection apparatus installed, use it, if not, install gravitationally injected equipment make chemical(20ltr) mix with water able to put in 1~2days on upper of Cascade Tank. Controlin put by installing valve in the middle
  • 5) If this method is difficult, put 100cc into Cascade Tank, control variation of input as test result
• 

• 1) Untreated boiler system, put BW TREAT 1.5-2.0Ltr boiler water per ton and keep P-Alkalinity about100-200ppm
• 2) After 24 hours, measure P-Alkalinity and control input in case of need, measuring Chloride Content, if Chloride quantity is excessive, do Surface Blow Down and Bottom Blow Down

• Remeasure P-Alkalinity and if need be, increase BW TREAT input and put at least 0.2Ltr in one day to keep proper figures of pH or P-Alkalinity

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Economical and mixture of high active phosphate
• B. Melt easily in water when input
• C. Decrease scales problem caused by calcium
• D. Keep accurate balance of phosphate
• E. Avoid sludge adherence and remove easily by Blow Down
• F. Decide level of treatment agent by simple test
• G. Not Alkalinity affected inside of system
• H. Usable on all pressure of boiler

• A. Boiler water treatment, Calcium scale preventives

• A. This product is one of respectively water treatment product
• B. Hardness Control is as if something manufactured to maintain clear phosphate levels is react with phosphate, and form a precipitate that not stick to metal surface, prevent forming calcium scales at accurate balance ofphosphate, make proper form by Blow Down

• A. Hardness Control is use to keep free phosphate level inside of boiler. This level is decided by boiler pressure,initial input is decided by water quality
• B. During normal operating, put Hardness Control 23g distilled water per ton to enhance 20ppm phosphate level
• C. To get accurate result, put Hardness Control into boiler directly through By-Pass put container installed in boiler water supply line
• D. Melt powder in hot water(50C) at the rate of 1 unit powder(ex. 500g/10 liter), put into 20 units of condensate water

• Hardness Control input g/Distilled water Ton

  Hardness Control input g/Distilled water Ton

  Pressure scope	Tested phosphate(PO4 ppm)						Standard scope PO4 ppm	Initial input g/Ton
  	0-10	10-20	20-30	30-40	40-50	Over 50
  0-40 BAR	23	11.5	Stable, Input needless			Blow Down	20-50	23
  41-60 BAR	23	11.5	Stable, Input needless			Blow Down	20-50	23
  Over 60 BAR	17	5.5	Stable	Blow Down			20-50	23

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Convenient treatment agent giving alkalinity to treat water well
• B. Prepare sure condition to help Hardness Control
• C. Help removing by Blow Down to precipitate magnesium chloride and calcium
• D. Neutralize acidity condition
• E. Improve efficiency, be economical by reducing maintenance
• F. Usable with most of chemicals
• G. Make silica material float, not attached
• H. Decide level of treatment agent by simple test
• I. Use to give required alkalinity condition in boiler
• J. Usable on all pressure of boiler
• K. Use as counteragent after acid rinsing work

• A.Treat boiler water, control corrosion and scale
• B. Use as counteragent after acid rinsing

• A. This product is using with Hardness Control, and one of respectively water treatment product
• B. Alkalinity Control is giving alkalinity condition to help Hardness Control, with accurate precipitation of hardened salinity, form scales when not made continuous Blow Down, get worse water flow and decline effect of heattransfer, occur partial corrosion as a result. Alkalinity Control is making alkali condition to help phosphatechemical to prevent these phenomenon
• C. Alkalinity Control also giving alkali condition required to corrosion control for neutralization of acid gas

• A. Proper treatment agent level is maintain by P.Alkalinity test, and decided by boiler type and pressure
• B. Refer input chart about accurate input rate, input chart is recommended figures based on experience
• C. Increasing method of alkalinity level is put required Alkalinity control quantity after doing P.Alkalinity test
• D. 225ml per ton of Alkalinity Control is increasing P.Alkalinity 100ppm
• E. To get accurate result, put Alkalinity Control into boiler directly through By-Pass put container installed in boiler water supply line

• A. Collect boiler water sample on 1~3days, and doing water test
• B. Sampling spot must same as according boiler pressure and type, and collect after regular Blow Down
• C. Samples are immediately cooled and tested
• D. Conduct test according to test equipment’s instruction, and write the resulting value to the Log Sheet

• Alkalinity Control input ml/Distilled water Ton

  Alkalinity Control input ml/Distilled water Ton

  Pressure scope	Tested P.Alkalinity ppm							Standard scope P.Alkalinity	nitial input ml/Ton
  	0-60	60-90	90-100	100-110	110-120	120-150	Over 150
  0-30 BAR	225	110	70	Stable, Input needless			Blow Down	100-150	280
  30-40 BAR	190	80	60	Stable, Input needless			Blow Down	100-130	280
  41-60 BAR	170	80	60	Stable, Input needless			Blow Down	100-120	280

  * On usual case : 225ml per ton of Alkalinity Control is increasing P.Alkalinity 100ppm
  pH is allowed to 10-11 for proper treat. This is recommended figures based on experience

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Easy-injection liquid product
• B. Prevent electrolyte corrosion by forming thin film on metal surface
• C. Be effective in Cavitation erosion
• D. Usable in non-metal, Seals, Glands, Packings, Hoses, Caskets, etc
• E. Usable mixture with anti-freeze of Glycol line
• F. Simple test

• A. Prevent corrosion of diesel engine coolant system and scale forming preventives

• A. CW TREAT is effective corrosion preventives for general iron or non-ferrous metal in coolant system using distilled water or fresh water
• B. Cover thin protective film on metal surface to prevent corrosion from electrolyte action caused between different metal used in system
• C. CW TREAT is not damaged on nonmetal material such as Seals, Clands, Packings, Hoses, Gaskets, used in these system generally
• D. As alkalinity mixture product, control corrosion damage such as Pitting, caused by acid, if put excessively by mistake, metal is not affected excess alkalinity or acidity by being alkalinity control in pH limit
• E. If system is polluted by oil or scale, before using CW TREAT remove oil and scale firt, use our neutral product as ALOHA SWING PLUS, TCS-3 PLUS on oil removal, use solvent line as TCS-3T, use DescalerPowder, Pescaling Liquid on scale remove
• F. If there be electric gilding part in system, before putting this treatment agent, cleaning system with Descaler Powder or Descaling Liquid is preferable
• G. CW TREAT is suitable in used heat source system’s preventives in fresh water generator for used of beverage
• H. It is usable mix with Glycol antifreeze when vessel is in cold area
• I. If there be aluminium component in system, prohibit using

• A. Enforce water test after circulation during several hours putting in Expansion Tanker

• A. CW TREAT must keep nitrite(No2) measure concentration 1500-3000PPM. Coolant per 1000ltr as follows:
• * NORMAL SPEED ENGINE

  NORMAL SPEED ENGINE

  Salinity	Initial input	No2 PPM
  Below 50 PPM	4 liter	1500-2300 PPM
  Below 50-100 PPM	6 liter	2300-3000 PPM

• * HIGH SPEED ENGINE

  HIGH SPEED ENGINE

  Salinity	Initial input	No2 PPM
  Below 50 PPM	6 liter	2300-3000 PPM

  * If put CW TREAT 1ltr per coolant 1000ltr, No2 concentration is increasing about 380 PPM

• B. For using coolant treatment agent correctly, coolant condition must have in below measure range

  For using coolant treatment agent correctly, coolant condition must have in below measure range

  Nitrite	1500-3000 PPM
  Chloride	Below NORMAL SPEED ENGINE 100 PPM Below HIGH SPEED ENGINE 50 PPM
  Hardness	180 PPM CaCo3
  pH	8.5-10.0

• C. Decide CW TREAT dosage by using NEW SHIN YOUNG Nitrite Test, do coolant test at least once a week

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Effective on removing all pollution
• B. Reduce time and cost by using chemicals dispenser
• C. Complete combustion in cylinder
• D. No damage in cylinder oil film
• E. Keep effectiveness of air cooler the best
• F. Usable soaking in cleaning tank or water tank
• G. Water solubility and superior in microorganism decomposition

• A. As Diesel engine air cleaner, effective on on-line and off-line clean, remove all pollutin quickly and not rusted cooler pin

• IN-SITU CIRCULATION METHODEngines are designed to cleanable air cooler in diriving. Circulate using installed clean equipment according manufacture’s instruction
• IMMERSION METHODDip air cooler in contatiner filled with ACC and water(10-30%), reduce clean time by heating upto about 40-50℃, soak 1-6 hours according polluted level. Cleaning effect will improve if stir with steam or pressure air. Wash with fresh water after cleaning, install to engine after dry. This method is advisable on machine parts sticking carbon precipitate stubbornly
• IN-SITU IMMERSION METHODFor this washing, stop engine and check safety. Fill overflowing the clutch with ACC and water(10-30%) mixture according polluted level and close the exit of cooler. For this process, settle 1-6 hours and emit on slop tank. Cleaning effect will improve if stir the steam or pressure air. Wash with fresh water after cleaning. Remove the closed exit and close the drain
• ON-LINE NETHODUse ACC by spraying on air cooler front trunk using chemicals dispenser provided by engine manufacturer or NEW SHIN YOUNG. ACC is mixed with water at 25% solution(water 3 liter per ACC 1liter ratio), spray using compressed air in air trunk through spray nozzle. Wash clearly by spraying fresh water after 10-20 minutes. Control chemical input and number according cooler size or condition, the dose is the same as in below table.

• A Pail packing : Actual capacity 25.00 ltr Plastic & Steel Pail packing
• 
  • 
  • 
    • 

• A. Low of toxic and irritation
• B. Non corrosiveness, safety of all kind of aluminum, light alloy
• C. Both simple and economical of immersion and circulation
• D. Be able reduce to hard scraping work
• E. Improved product to cleaning specification
• F. Developped product for industry
• G. It is not containing phenolic and chloric hybrid
• H. Low evaporation
• I. Not need special equipment
• J. Extraordinary cleaning for piston, piston ring, valve spring, valve cage
• K.Extraordinary remove for all polluted by wood oil, varnish or carbon, and, carbon type stained on fuel sprayer, tip of gas stove
• L. Cleaning for oil part side of feul, lubricant heater, oil cooler etc
• M. Extraordinary remove for carbonic sediment feul oil, lubricant filter
• N. Being constrict of rubber, plastic

• A. Cleaner to carbon, tar, oil dust of each part to vessel engine, engine of shorebase, repair of other machinery
• B. Used to clear of gas stove tips, oil cooler, oil heater etc to repair
• C. Used to clear of dessel engine block, gear box, piston, ring, valve, pipe etc to repair

• A. Dilution ratio : Using original liquid is take superior effect
• B. Usage temperature : Capable to usually condition but 40-60C is more effect
• C. Washing tips : Be able to extraordinary effect in using immersion to remove carbon, both spray and immersion
• D. Immersion way :
  • 1) Best applicable method to remove sediment of machinery parts and an edifice, Parts are flooded in TCS-CR
  • 2) Use 1 : 2 dilution water and sediment is removed in 1 time when remove light oil or light sediment, is able to remove during immerse 5-24 times when terribly oxidized
  • 3) Wipe off brush or sponge after immerse for 5-6 times in TCS-CR origin liquid when fixed carbon
  • 4) Not need to care by very low evaper ratio for prevent from loss to vaper, only need to ventilate relevantly
• E. Cycling tips : This is let liquid to cycle in everywhere until wash finished, should confirm whichever cycle or not completely in everywhere in case of adopt this way
• F. Required time : About 1-2 times require( is removed in one night)

• A Pail packing : Actual capacity 25.00 ltr Plastic & Steel Pail packing

• A. Don’t contact with humanbody and clothes due to solvent type
• B. Work in good ventilated place
• C. Wash in the running water sufficiently when contacted on skin or eyes, mouth
• D. Must wear on safety protecting equipment same as antichemical gloves necessary when use it
• E. Don’t use except usage
• F. Should close cap after use
• G. Don’t use near firearm
• H. Avoid sunlight and storage cooling darkness
• I. Don’t load more 3 stages
• J. Refer to technical data and MSDS about others detail information

• A. Remove scales and oxidized steel quickly and effectively
• B. Acid product for restrain corrosion of ferrous metal
• C. Quick remove of rust and discolor, prevent spread of rust
• D. Extensive dilution ratio
• E. Containing scale remove improvement agent to increase re-reaction
• F. Remove inconvenient for decomposing for inner cleaning
• G. Water soluble and noninflammability, improve workplace
• H. High concentrated product
• I. Infinity shelf life
• J. Quick rinsing

• A. Remove boiler scale and oxidized steel(rust)
• B. Remove diesel engine coolant system scale and oxidized steel(rust)
• C. Remove heat exchanger, water heater, fresh water generator, condenser scale and oxidized steel(rust)

• A. In big system or component, most effective scale removal is rotation method, and on small component, use dipping method using water tank
• B. If equipment is polluted by grease, sludge, carbonaceous, oil, get the best effect when clean first with required cleaner such as neutrality product -TCS-3PLUS, ALOHA SWING PLUS-, solvent product -TCS-3T
• C. Mixture 10-30% water solution with fresh water according scale degree
• D. This product is always using in plastic container, add solution on water, do not contrary to this
• E. After using Descaling Liquid, it is essential to wash with 0.5% Alkalinity product Alkalinity Control water solutionall metal surface at least once all around. Circulate this water solution 2-4 hours to get proper PH figure. PHfigure be around neutrality(PH7), neutralize any acid residue and passivated metal
• F. Descaling Liquid do not use in aluminium, zinc, tin, tinplate sheet

• A. Make forced circulation circuit (pipe line)
• B. Remove zinc, aluminium, plated material
• C. Wash sludge, mud with water
• D. Make 10-20% diluted solution according to scale type and pollution level
• E. Install Air Vent on the highest place of circulation loop, select sample place to open easily, it is convenience that progress working with check progress of scale remove
• F. Vary with chemical concentration and scale level, but circulate 1-4 hours in case of oxidized steel, 24-36 hours in case of Hardness Scale. Clean time is shorten if heated, but heat temperature must not over 40℃
• G. When chemical concentration is declined, put additional. Add below 1/2 of initial putting quantity considering uniformity of chemical concentration
• H. If scale is removed, bubble caused by circulation solution is disappear (check sample)
• I. Circulate 1 hour more and wash with water after draining solution
• J. Neutralize 2-6 hours with 0.5-2% alkali product, Alkalinity Control

* TCS-3, ALOHA, ALOHA SWING, TCS-5 product is possible when Alkalinity Control is not in vessel

• A. Check in the same way as circulation method, put clean material into solution after maintenance remove working
• B. Cleaning time is shorten when stir solution or disturb solution by blowing air

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Easy and safe on storage and handling, carriage as powder product
• B. Remove scale and rust quickly and effectively
• C. Prevent metal by containing corrosion preventives
• D. Reduce cleaning time by containing scale removal increasing agent
• E. Containing bubble preventives

• A. Remove boiler scale and oxidized steel(rust)
• B. Remove diesel engine coolant system scale and oxidized steel(rust)
• C. Remove heat exchanger, water heater, fresh water generator, condenser scale and oxidized steel(rust)

• A. In big system or component, most effective scale removal is rotation method, and on small component, usedipping method using water tank
• B. If equipment is polluted by grease, sludge, carbonaceous, oil, get the best effect when clean first with requiredcleaner such as neutrality product -TCS-3PLUS, ALOHA SWING PLUS-, solvent product -TCS-3T
• C. Mix 3-10% water solution with fresh water according scales degree, get the appropriate intensity. If possible, make water solution heating 50-60℃ always
• D. Neutralize with 1-2% alkali product, Alkalinity Control, with fresh water after using Descaler Powder
• E. Descaling Powder do not use in aluminium, zinc, tin, electric gilded surface

• A. Make forced circulation circuit (pipe line)
• B. Remove zinc, aluminium, plated material
• C. Wash sludge, mud with water
• D. Make 5-10% diluted solution according scale type and pollution level
• E. Install Air Vent on the highest place of circulation loop, select sample place to open easily, it is conveniencethat progress working with check progress of scale remove
• F. Vary with chemical concentration and scale level, but circulate 1-4 hours in case of oxidized steel, 24-36 hoursin case of Hardness Scale. Clean time is shorten if heated, but heat temperature must not over 60℃.If over 35℃, occur slight acid corrosion on light alloy metal and zinced surface
• G. When chemical concentration is declined, put additional. Add below 1/2 of initial putting quantity consideringuniformity of chemical concentration
• H. If scale is removed perfectly by opening sample place, wash with water sufficiently after drain
• I. Circulate 1 hour more and wash with water sufficiently after draining solution
• J. Neutralize 2-6 hours with 1-2% alkali product, Alkalinity Control

* TCS-3, ALOHA, ALOHA SWING, TCS-5 product is possible when Alkalinity Control is not in vessel

• A. Check in the same way as circulation method, put clean material into solution after maintenance remove working
• B. Cleaning time is shorten when stir solution or disturb solution by blowing air

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Reduce soot and sludge precipitate
• B. Reduce cold-end corrosion
• C. Improve heat transfer and effectiveness
• D. Improve effectiveness of boiler
• E. Assist soot blowing

• A. Remove deposited/accumulated carbon slag in boiler furnace, superheater, economizer, exhaust way

• A. If Firescale is formed in heat exchanger, heat loss directly increase excessive fuel consumptionAbout 1mm precipitate causes about 10% heat loss, 3mm precipitate causes up to 50% heat loss
• B. Soot general ignition point is about 600℃, this means it burned on the hottest spot in diesel exhaust system or boiler
• C. As catalysis of Soot Remover, Soot Firescale ignition point is below about 280℃.Carbon precipitate be left aches can be easily ignited and removed
• D. Use of Soot Remover is enlarging effectiveness of fuel, also prevent forming acid causing serious corrosion on heat exchanger, superheater, economizer, exhaust way stack

• A. Blow Soot Remover into boiler through proper pot using blower
• B. Powder must sprinkle through rear flame passage of combustor
• C. In diesel engine, spray Soot Remover directly to upper to be processed spot of exhaust system
• D. If Soot Remover injection Unit is installed, put proper amount through equipment
• E. Decide input refer as followings

• Usage methods and dosing ratio

  Oil consumption(ton) one day	20	40	60	80	100	120
  Chemical input	1	2	4	6	9	10

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Usable in low exhaust temperature spot
• B. Reduce soot and sludge precipitate
• C. Reduce cold-end corrosion
• D. Improve effectiveness of heat transfer
• E. Improve effectiveness of boiler
• F. Assist soot blowing
• G. Reduce cold-end corrosion caused in lower surface temperature than dew point of exhaust gas

• A. Remove soot and firearms scale precipitate in boiler exhaust system and diesel engine

• A. If Firescale is formed in heat exchanger, heat loss directly increase excessive fuel consumptionAbout 1mm precipitate causes about 10% heat loss, 3mm precipitate causes up to 50% heat loss
• B. Soot general ignition point is about 600℃, this means it burned on the hottest spot in diesel exhaust system or boiler
• C. As catalysis of Soot Remover, Soot Firescale ignition point is below about 280℃.Carbon precipitate be left aches can be easily ignited and removed
• D. Use of Soot Remover is enlarging effectiveness of fuel, also prevent forming acid causing serious corrosion on heat exchanger, superheater, economizer, exhaust way stack

• A. Boiler : Sprinkle through rear flame passage of boiler combustor room, through suitable pot or sprayer
• B. Diesel Engine : Spray on upper to be processed spot of exhaust system through input equipment

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Low of toxic and irritation
• B. Non corrosiveness, safety of all kind of aluminum, light alloy
• C. Both fastly penetrated and reaction
• D. Developped product for industry
• E. It is not containing chloric solvent mixture
• F. Powerful agent controlled evaporation
• G. Be able to cleaning by nonconductive without disassemble motor
• H. Remove to oil of electric equipment and wash not need to rinse
• I. Effective wash not to remain stain and water dust of grease
• J. No damage where is applicated to nonelectric equipment
• K. Promptly remove extraneous matter to oil dust, oil, metal powder, carbon
• L. Extraordinary cleaning to generator, distributing board, resistance dust, motor etc
• M. Being constrict of products of rubber, plastic

• A. Remove oil of motor, print machinery, electric networking board
• B. Remove oil of communication instrument, distributing board, control board etc
• C. Remove oil of part of electric some
• D. Cleaning wash of precision apparatus

• A. Dilution ratio : Use original liquid
• B. Usage temperature : More effective to use usual temperature
• C. Washing tips : Immersion, spray, brush, wipe off etc
  • 1) Immersion way : Can remove during short immersion time in water container
  • 2) Spray way : Use hand sprayer or siphon sprayer by best way, easily be evaporable by low pressure air of Remaining solvent after removed dust, grease
  • 3) Wipe off polluted material by brush or cloth in liquid
  • 4) Although anysome can be damaged on plastic or rubber, but is usable to actually wash out of all kind of electric device and composition
  • 5) Eliminate rubber or plastic of assemble before cleaning, or is good to watch react of test on the part, Should protestant test after cleaning to motor or generator
  • 6) Care : Exhibit in running generator or motor

• A Pail packing : Actual capacity 25.00 ltr Plastic & Steel Pail packing

• A. Don’t contact with humanbody and clothes due to solvent type
• B. Work in good ventilated place
• C. Wash in the running water sufficiently when contacted on skin or eyes, mouth
• D. Must wear on safety protecting equipment same as antichemical gloves necessary when use it
• E. Don’t use except usage
• F. Should close cap after use
• G. Don’t use near firearm
• H. Avoid sunlight and storage cooling darkness
• I. Don’t load more 3 stages
• J. Refer to technical data and MSDS about others detail information

• A. Acid product containing surfactant
• B. Remove seriously attached hard precipitate
• C. Acted quickly, completely and inducing efficiency of centrifugation
• D. Not containing phenolic and estrogen compound
• E. Be able to clean dispense without the need for detaching separator and disc part
• F. Non plasticity
• G. Cost-effective and easy to use

• A. Be effetive on removing carbon contained precipitate, from all kinds of cleaner and cleaner disc
• B. Clean parts of decomposed equipment

• A. Disclean Purifier is able to use diluting to 20% with fresh water or original solution as it is, cleaning work is effective by using more original solution. It is usable by heating, or having the time, until rinse workingis finishing
• B. Rinse working takes time 30minutes-2hours according to polluted level, and be able to remove pollution quickly and effectively by heating up to 60℃
• C. After component or equipment is clean well, wash all around with fresh water, remove Disclean Purifier and all polluted trace
• D. This product is not recommended for use on aluminium alloy, electric gilding, tin, zinc

• A. Take out piled disc of cleaner and put into Disclean Purifier solution
• B. Effect on removing pollution if circulating or heating solution
• C. Take out piled disc of cleaner, and separating the disc, dip into Disclean Purifier tank Be circulating or heating is effective
• D.If unable to get a water tank, spray by wearing protective clothes, eye/face protection equipment and gloves described in product MSDS

• A. Pail packing : Actual capacity 25.00 ltr Plastic Pail packing

• A. Non-corrosive, and be usable safely on all kinds of filter safely
• B. Remove seriously attached hard precipitate
• C. By cleaning thoroughly and perfectly, and keep, conserve, protect the operation performance of filter
• D. Apply quickly and effectively
• E. Remove oil and grease deposition easily
• F. Usable in all metals and alloys stably
• G. Attack the oil, emulsion, condensed liquid, and dissolving
• H. Cost-effective and easy to use

• A. Remove oil and deposition of all kinds of filter and machine equipment

• A. Conduct in circulation or dip method
• B. If circulation method, decide filter capacity and circulate 5-10 hours in regular speed
• C. If dip method, leave filter soak in water tank for 5-10 hours
• D. Use in not diluted condition, and if dip method, needed a regular stirring

• A. Because solvent-based, don’t contact with human and clothes
• B. Work in good ventilated place because it occur gas
• C. Don’t look in container during ventilation
• D. Must wear on safety protecting equipment same as antichemical gloves necessary when use it
• E. Don’t use except usage
• F. Should close cap after use
• G. Don’t use near firearm
• H. Avoid sunlight and storage not to freeze
• I. Don’t load more 3 stages
• J. Refer to technical data and MSDS about others detail information

• A. Pail packing : Actual capacity 20.00 ltr Plastic Pail packing